IEC 61000-4-2 ESD Testing: Setup, Discharge Points, Fixes
How IEC 61000-4-2 ESD testing works: contact and air discharge, test levels, HCP and VCP setup, choosing discharge points, pass criteria and TVS fixes.
Electrostatic discharge is the immunity test that most often turns a quiet product into a resetting one. A person walks across a carpet, touches a metal connector shell, and a few nanoseconds of current at tens of amperes flow through whatever path the product offers. IEC 61000-4-2 defines how to reproduce that event repeatably: the generator, the waveform, the test setup and the procedure. Product standards such as CISPR 35, IEC 61000-6-1 and IEC 61000-6-2 then choose the levels and the required result.
What the ESD generator reproduces
The generator models a person holding a small metal object, such as a key, as a 150 pF capacitor discharged through 330 Ω. For contact discharge, the first current peak is 3.75 A per kV with a rise time of 0.8 ns (±25 %), followed by a broader hump that is still 2 A per kV at 30 ns and 1 A per kV at 60 ns.
| Level | Contact discharge | Air discharge | First peak current (contact) | Current at 30 ns | Current at 60 ns |
|---|---|---|---|---|---|
| 1 | 2 kV | 2 kV | 7.5 A | 4 A | 2 A |
| 2 | 4 kV | 4 kV | 15 A | 8 A | 4 A |
| 3 | 6 kV | 8 kV | 22.5 A | 12 A | 6 A |
| 4 | 8 kV | 15 kV | 30 A | 16 A | 8 A |
Currents are for contact discharge, from IEC 61000-4-2 Ed. 2 (tolerance ±15 % on the first peak and ±30 % at 30 ns and 60 ns).
The fast edge is what makes ESD an RF problem as much as a high-voltage one. With the bandwidth rule BW ≈ 0.35 / t_r, a 0.8 ns rise time corresponds to about 437.5 MHz, and the knee frequency 0.5 / t_r is 625 MHz. At those frequencies a few centimetres of wire or trace are no longer a short circuit, and the field from the discharge couples into nearby traces and cables even when no current enters the circuit directly.
Test setup: table-top and floor-standing
The test is done over a metal ground reference plane (GRP) on the floor, connected to protective earth. A table-top EUT sits on a 0.8 m high non-conductive table carrying a horizontal coupling plane (HCP) of 1.6 m × 0.8 m; the EUT and its cables are insulated from the HCP by a 0.5 mm insulating support. Floor-standing equipment stands on an insulating support about 0.1 m high above the GRP. Coupling planes are connected to the GRP through a cable with a 470 kΩ resistor at each end, so that they take up charge during a discharge and then bleed it off slowly, like real metal furniture.
Ungrounded equipment, such as battery-powered devices or products with a two-wire power cord, needs extra care. Each discharge leaves charge on the EUT, and if it is not removed the next discharge sees a smaller voltage difference, so the test becomes milder than intended. IEC 61000-4-2 Ed. 2 requires the charge to be removed before each discharge, for example with a bleeder cable with 470 kΩ resistors connected to the GRP.
Contact, air, direct and indirect discharge
Contact discharge is the preferred method. The sharp tip touches the conductive point first, then a relay inside the generator fires. Paint is penetrated with the tip unless the manufacturer declares it to be insulation. Air discharge is used where contact discharge cannot be applied, such as insulating surfaces, gaps and seams: the charged round tip is moved toward the EUT as fast as possible until a spark jumps. Air discharge depends on approach speed, humidity and tip condition, so results scatter more; this is one reason the standard defines climatic conditions for the test, including relative humidity from 30 % to 60 %.
Direct discharge goes to points on the EUT that people can touch. Indirect discharge simulates a discharge to nearby metal: contact discharges are applied to the edge of the HCP at 0.1 m from the EUT, and to the edge of a 0.5 m × 0.5 m vertical coupling plane (VCP) placed 0.1 m from each side of the EUT. Indirect discharge drives no current into the EUT, only a transient field, so it often finds weaknesses in unshielded cables and plastic housings.
Choosing discharge points
- Connector shells and the metal parts of I/O ports (USB, Ethernet, HDMI, audio jacks).
- Buttons, keypads, touch screens and display edges, where a spark can jump through a gap to the electronics behind.
- Seams, ventilation slots and screw heads in plastic or metal housings (air discharge at gaps, contact discharge at screws).
At each selected point, apply single discharges in both polarities, typically at least ten per polarity, about 1 s or more apart. Test the lower levels as well: an air discharge at 2 kV or 4 kV can upset a circuit that survives 8 kV, because the spark forms across a shorter gap and its edge can be faster.
Pass criteria and typical levels
IEC 61000-4-2 classifies the result: (a) normal performance within the specified limits; (b) temporary loss of function or degradation that recovers by itself; (c) temporary loss of function that needs operator intervention or a system reset; (d) loss of function that cannot be recovered because of damage to hardware or software, or loss of data. The product standard says which class is acceptable, and the test plan must state what normal performance means for the EUT, for example no reset, no change of a displayed value, or no more than a stated error rate on a data link.
| Standard | Contact | Air | Required result |
|---|---|---|---|
| CISPR 35 (multimedia equipment) | ±4 kV | ±8 kV | Criterion B |
| IEC 61000-6-1 (residential, commercial, light industry) | ±4 kV | ±8 kV | Criterion B |
| IEC 61000-6-2 (industrial) | ±4 kV | ±8 kV | Criterion B |
| IEC 60601-1-2 Ed. 4 (medical) | ±8 kV | ±2, ±4, ±8, ±15 kV | Basic safety and essential performance maintained |
Automotive ESD follows ISO 10605, which uses other discharge networks and levels set by the vehicle manufacturer.
Design measures that work
The goal is to give the discharge current a short, low-inductance path to chassis or ground that does not cross sensitive circuits. Inductance matters far more than DC resistance. Take a level 4 contact discharge: 30 A first peak with a 0.8 ns rise time. The average slope over the 10–90 % rise is 0.8 × 30 A / 0.8 ns = 30 A/ns, so an extra 10 nH in the ground connection of a TVS diode adds V = L · di/dt = 300 V on top of its clamping voltage. At 437.5 MHz the same 10 nH has a reactance of 27.5 Ω, far more than the dynamic resistance of a good TVS diode.
- Place TVS diodes at the connector, before anything else on the line, and connect them to ground or chassis with short, wide traces and several vias.
- Route the line from the connector through the TVS pad and then to the IC, not as a stub, so the current reaches the clamp before the chip. A series resistor or ferrite bead between the TVS diode and the IC shares the residual voltage.
- Choose the TVS diode for the signal: low capacitance (below 1 pF for high-speed lines such as USB 3 or HDMI), a working voltage above the normal signal level, and a low clamping voltage at the rated pulse current.
- In plastic housings, keep traces and components away from seams and openings, and lengthen the air path at buttons and displays so a spark cannot reach the circuit.
- In firmware, use a watchdog, refresh critical peripheral registers periodically, and re-establish communication links automatically; this often turns a criterion C result into criterion B.
Common mistakes
- Testing an ungrounded product without removing charge between discharges, which makes an in-house test milder than the lab's and gives a false pass.
- Not defining normal performance in the test plan, so the lab and the manufacturer argue about whether a display flicker or a dropped packet is a failure.
- Placing the TVS diode next to the IC instead of the connector, or connecting it to ground through a long trace.
Calculators used in this post
More posts
Results and summaries are for reference. For certification and test reports use the latest official standard text and calibrated instrument data.