Enclosure Shielding: Seams, Gaskets, Vents and Cable Entries

Why metal enclosures leak at seams, slots and cable entries rather than through the wall: screw pitch, gasket types, honeycomb vents, wall filters and checks.

Published: 2026-11-15 · Last updated: 2026-11-21

A metal box looks like a perfect shield, yet many products with metal enclosures still fail radiated emissions or radiated immunity. Above a few megahertz almost any sheet metal is thick enough; what decides the result is how the box is put together: the seams between panels, the openings for ventilation and displays, and every cable that passes through the wall.

Why the openings set the shielding, not the metal

For aluminium (about 35 MS/m) the skin depth at 100 MHz is about 8.5 µm, so a 1 mm wall is more than 100 skin depths thick and its theoretical absorption loss is far beyond anything a test can measure. Real enclosures achieve much less because the currents induced on the inside of the wall must flow around the box without interruption. Any opening that cuts across their path forces the current around it, and the opening then radiates like a slot antenna. That is why the longest dimension of an opening matters, not its area: a 100 mm × 1 mm slot leaks far more than a round 10 mm hole, although their areas are similar.

A common first estimate for a single opening with longest dimension L is SE ≈ 20·log₁₀(λ / 2L), valid while L is shorter than λ/2. Once L reaches λ/2, at f = c / 2L, the opening is resonant and gives almost no shielding. For n identical openings close together, subtract roughly 10·log₁₀(n).

OpeningEstimated SE at 300 MHzEstimated SE at 1 GHz
One 100 mm slot14.0 dB3.5 dB
20 holes of 5 mm in a row (same 100 mm length)27.0 dB16.5 dB
One 5 mm hole40.0 dB29.5 dB
Seam touching only at screws every 50 mm20.0 dB9.5 dB
Seam touching only at screws every 15 mm30.5 dB20.0 dB

Estimates from SE ≈ 20·log₁₀(λ / 2L) − 10·log₁₀(n). Real values depend on wall thickness, hole spacing and where the opening sits relative to internal sources.

Splitting one 100 mm slot into 20 small holes gains about 13 dB at both frequencies in this example, which is the basic logic behind every perforated vent panel. The 100 mm slot stops shielding altogether at 1499 MHz, where it becomes a half-wave slot antenna.

Seams and joints

Where two panels meet, the seam is a long slot unless the surfaces touch electrically along its whole length. If contact is made only at the screws, the seam behaves like a row of slots, each as long as the screw pitch. The usual rule of thumb, a pitch no larger than λ/20 at the highest frequency of concern, corresponds to about 20 dB with the formula above. A 50 mm screw spacing gives that at 300 MHz but only 9.5 dB at 1 GHz, where the pitch would have to come down to 15 mm.

  • Make contact surfaces conductive. Anodising and most paints are insulators; mask the flanges during painting, or use a conductive finish such as a chromate or trivalent conversion coating or nickel plating on the contact areas.
  • Prefer overlapping or folded joints to butt joints. An overlap of several millimetres forms a capacitive path even where the metal does not touch, and a stiff flange keeps contact pressure between screws.
  • Check galvanic compatibility. Dissimilar metals in a humid environment corrode, and the oxide raises contact resistance over the product's life; galvanic compatibility tables, for example in MIL-STD-889, help choose finishes and gasket materials.

Choosing a gasket

A gasket fills the seam with a compliant conductor so that contact is continuous without dozens of screws. It only works when compressed within the manufacturer's specified range: too little compression leaves gaps, too much causes permanent set or damage. Design the flange with a groove or compression stop that holds the right gap under real tolerances.

Gasket typeStrengthsLimitationsTypical use
Beryllium-copper or stainless-steel fingerstockVery good high-frequency contact, low closure force, tolerates frequent openingNo environmental seal; fingers can snag or breakDoors, drawers, removable covers
Conductive elastomer (silicone filled with silver, silver-aluminium or nickel-graphite particles)EMC and environmental (water and dust) seal in one partHigher closure force; filler must suit the flange finish to limit corrosionOutdoor and sealed housings
Knitted wire mesh, with or without an elastomer coreRobust and inexpensiveTakes a compression set after repeated cyclesFixed covers and panel joints
Fabric-over-foamSoft, low closure force, wide compression rangeNot for frequent wear or wet environmentsElectronics enclosures, I/O panels, shield cans

Vents, displays and other apertures

When a perforated panel is not enough, a honeycomb panel uses the waveguide-below-cutoff effect. Each cell is a short waveguide with a cutoff frequency f_c = c / (2w) for a rectangular cell of width w. Below cutoff the field decays along the cell, adding about 27.3 dB for every cell width of depth: SE ≈ 27.3 · (t/w) · √(1 − (f/f_c)²). For 5 mm cells f_c is about 30 GHz, and a 10 mm deep honeycomb adds about 54.5 dB at 1 GHz, while a 0.5 mm sheet with the same holes adds only 2.7 dB on top of the aperture term. The honeycomb delivers this only if its frame is bonded to the panel all the way round, usually with a gasket.

  • Displays and windows: use conductive coated glass or film (transparent conductive oxide or fine metal mesh) and bond it to the frame along its whole edge with a conductive busbar and gasket.
  • Controls and light paths: a metal shaft through the panel carries internal noise outside. Use an insulating shaft, or pass it through a metal tube that works as a waveguide. Light pipes and optical fibres are non-conductive, so they can pass through small holes or waveguide tubes.

Cable entries: where shielding is usually lost

A conductor that passes through the wall carries internal noise straight past every seam and gasket, and outside it radiates as a cable antenna. Every conductor that crosses the boundary needs one of two treatments at the wall itself: a shield bonded 360° to the panel at the entry point, or a filter that returns high-frequency current to the wall before it crosses, such as a feedthrough capacitor, a filtered connector or a panel-mounted filter. A filter on the PCB a few centimetres inside the box works less well, because the wire between it and the wall picks up internal fields again. Shield termination and the pigtail problem are covered in our earlier post on cable shields.

Cavity resonance

A closed metal box is also a resonator. The resonant frequencies of a rectangular box of width a, depth b and height d are f = (c/2) · √((m/a)² + (n/b)² + (p/d)²), where at least two of the integers m, n and p are non-zero. A 300 × 200 × 100 mm box has its first resonances at about 901, 1249 and 1580 MHz. Near those frequencies internal fields build up, a small slot leaks much more than the slot formula predicts, and emissions show narrow peaks that move when a board or cable is relocated inside. Absorber sheet inside the lid damps the resonance.

Design review checklist

  • Write down the highest frequency of concern for emissions and immunity and convert it to λ/20; no slot, seam gap or contact spacing should exceed that length.
  • Confirm that every cable crosses the wall through a 360° shield termination or a wall-mounted filter.
  • Check gasket compression and closure force with worst-case flange tolerances, not nominal dimensions.
  • On the prototype, scan seams, vents and connectors with a near-field probe while a battery-powered comb generator runs inside the closed box; readings with and without the enclosure give the insertion loss (formal method for small enclosures: IEEE Std 299.1).

Common mistakes

  • Painting or anodising the whole part, flanges included, and discovering it only at the test lab.
  • Adding screws until the seam passes at one frequency, while a resonance at a higher frequency remains.
  • Fitting an expensive gasket but letting a cable pass through a plastic grommet with no filter or shield bond.
All dB values here are first-order estimates from simple formulas (single-aperture slot, waveguide below cutoff, ideal rectangular cavity). Use them to compare design options, not to predict a test result.

Calculators used in this post

More posts

Results and summaries are for reference. For certification and test reports use the latest official standard text and calibrated instrument data.